刀片服务器组网查询工具使用指导

非经本公司书面许可，任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部，

并不得以任何形式传播。本文档中的信息可能变动，恕不另行通知。

工具介绍 ···············································································································································1-1

1

.1 主要功能 ············································································································································1-1

.2 使用场景 ············································································································································1-1

1

操作指导 ···············································································································································2-1

2.1 操作步骤 ············································································································································2-1

2

.1.1 自定义组网查询 ······················································································································2-1

.1.2 典型样例查询 ························································································································2-11

2

2.2 导出查询结果 ···································································································································2-12

2

.2.1 导出自定义组网查询结果 ······································································································2-12

.2.2 导出典型样例查询结果 ·········································································································2-13

2

i

1

工具介绍

1

.1 主要功能

•

查询刀片服务器中 Mezz 网卡的端口，与互联模块内部端口的连接关系。

查看刀箱各个业务场景下的内部互联情况。

1

.2 使用场景

•

已装配刀箱的组网查询和验证。

配置 Mezz 网卡或互联模块前，查询端口连接关系。

刀箱扩容前的组网验证。

2

操作指导

2

.1 操作步骤

2

.1.1 自定义组网查询

(1) 选择自定义组网查询页签。

单击自定义组网查询页签，进入自定义组网查询页面。

2

-1

图2-1 选择工具页签

(2) 选择刀箱主机型号。

在工具左侧主机型号栏目中，单击选择 H3C UniServer B16000。

2

-2

图2-2 选择刀箱主机型号

(3) 选择各节点槽位对应的刀片服务器，并配置刀片服务器上的 Mezz 网卡。

例如，在 15 槽位下拉框中选择 B5700 G5，如图 2-3 所示。

如图 2-4 所示，刀箱前部的节点槽位有四个安装区域，每个安装区域内不支持混插半宽节点和

全宽节点。如图 2-5 所示，对于全宽节点只能在奇数槽位选择，选定后右侧的偶数槽位将被锁

定。

2

-3

图2-3 选择刀片服务器

图2-4 四个安装区域

2

-4

图2-5 半宽节点和全宽节点

(4) 在Mezz网卡下拉框选择刀片服务器上的 Mezz网卡型号，未安装 Mezz网卡的槽位可以为空。

例如，在 Mezz 网卡下拉框选择 Mezz1、Mezz2 和 Mezz3 均为 IB1040i。

图2-6 选择刀片服务器

2

-5

(5) 通过克隆操作复制型号相同且 Mezz 网卡配置相同的刀片服务器。

a. 单击<克隆节点>按钮，然后单击待复制的节点的对应的<复制>按钮。

图2-7 选择刀片服务器及 Mezz 网卡

b. 勾选待克隆的节点，然后单击<克隆至选中节点>按钮。

2

-6

图2-8 选择刀片服务器及 Mezz 网卡

如图 2-9 所示，可以单击节点槽位或节点槽位视图查看指定槽位的 Mezz 网卡配置情况。

2

-7

图2-9 查看 Mezz 网卡配置情况

(6) 在互联模块的下拉框中指定互联模块型号。

图2-10 选择互联模块型号

2

-8

(7) 单击<下一步>按钮查看连线视图。

图2-11 查看连线视图

(8) 选择节点槽位，可以在查询结果中查看 Mezz 网卡的端口与互联模块内部端口的连接关系。

2

-9

图2-12 选择节点槽位

(9) 将鼠标移动至连线处，可以亮显连线两端的端口号

图2-13 亮显连线关系

2

-10

(10) 单击<表格视图>按钮查看节点槽位连线的表格视图。

图2-14 表格视图

2

.1.2 典型样例查询

(

1) 选择典型样例查询页签。

单击典型样例查询页签，进入典型样例查询页面。

图2-15 选择工具页签

(2) 选择典型样例。

先选择业务类型，然后选择典型样例。

2

-11

图2-16 选择典型样例

2

.2 导出查询结果

2

.2.1 导出自定义组网查询结果

工具支持查询结果导出。选择节点槽位后单击<导出图片>可以导出此节点的连线视图，单击<导出

所有节点图片>可以导出所有节点的连线视图，查询结果以 png 图片的形式导出。

2

-12

图2-17 导出自定义组网查询结果

2

.2.2 导出典型样例查询结果

工具支持查询结果导出。选择节点槽位后单击<导出图片>可以导出此节点的连线视图，单击<导出

所有节点图片>可以导出所有节点的连线视图，查询结果以 png 图片的形式导出。

2

-13

图2-18 导出典型样例查询结果

2

-14